? semiconductor components industries, llc, 2002 march, 2002 rev. 0 1 publication order number: nup6101dmr2/d nup6101dmr2 advance information unidirectional tvs array for high-speed data line protection the nup6101dmr2 transient voltage suppressor is designed to protect equipment attached to up to six high speed communication lines from esd, eft, and lightning. features: ? micro8 package ? peak power 300 watts 8 x 20 s ? esd rating: iec 6100042 (esd) 15 kv (air) 8 kv (contact) iec 6100044 (eft) 40 a (5/5 ns) iec 6100045 (lighting) 23 a (8/20 s) ? ul flammability rating of 94 v0 typical applications: ? high speed communication line protection ? 5.0 v data and i/o lines ? microprocessor based equipment ? lan/wan equipment ? servers ? notebook and desktop pc ? instrumentation maximum ratings rating symbol value unit peak power dissipation 8 x 20 s @ t a = 25 c (note 1) p pk 300 w peak pulse current 8 x 20 s @ t a = 25 c (note 1) i pp 17 a junction and storage temperature range t j , t stg 55 to +150 c lead solder temperature maximum 10 seconds duration t l 260 c 1. nonrepetitive current pulse 8 x 20 s exponential decay waveform this document contains information on a new product. specifications and information herein are subject to change without notice. 6101 = device code a = assembly location y = year w = work week 1 8 device package shipping ordering information nup6101dmr2 micro8 4000 tape & reel micro8 case 846a http://onsemi.com ayw marking diagram 6101 source 1 2 3 4 8 7 6 5 top view source source gate drain drain drain drain pin assignment 1 2 3 4 8 7 6 5
nup6101dmr2 http://onsemi.com 2 electrical characteristics characteristic symbol min typ max unit reverse standoff voltage v brwm 5.0 v reverse breakdown voltage @ i t = 1.0 ma v br 6.0 v reverse leakage current @ v rwm = 5.0 volts, t = 25 c i r 20 a maximum clamping voltage @ i pp = 1.0 a, 8 x 20 s v c 9.8 v maximum clamping voltage @ i pp = 5.0 a, 8 x 20 s v c 11 v maximum peak pulse current i pp 17 a junction capacitance between i/o pins and ground @ v r = 0 v, 1.0 mhz c j 400 pf % of peak pulse current figure 1. pulse width figure 2. 8 20 s pulse waveform 100 10 1 1 10 100 1000 t, time ( s) 1000 note: nonrepetitive surge. 100 90 80 70 60 50 40 30 20 10 0 020406080 t, time ( s) t p t r pulse width (t p ) is defined as that point where the peak current decay = 8 s peak value i rsm @ 8 s half value i rsm /2 @ 20 s p pk , peak surge power (watts)
nup6101dmr2 http://onsemi.com 3 figure 3. clamping voltage versus peak pulse current figure 4. typical derating factor for duty cycle 8 4 0 01015 30 i pp , peak pulse current (a) 12 v c , clamping voltage (v) figure 5. typical leakage current versus temperature derating factor 1 ms 10 m s 1 0.7 0.5 0.3 0.05 0.1 0.2 0.01 0.02 0.03 0.07 100 m s 0.1 0.2 0.5 2 5 10 50 1 20 100 d, duty cycle (%) pulse width 10 ms 52025 2 10 6 4 2 0 100 0 50 200 t, temperature ( c) 8 i r , typical leakage current ( a) 50 100 150 1 7 3 6 5 series 1
nup6101dmr2 http://onsemi.com 4 package dimensions micro8 case 846a02 issue e s b m 0.08 (0.003) a s t dim min max min max inches millimeters a 2.90 3.10 0.114 0.122 b 2.90 3.10 0.114 0.122 c --- 1.10 --- 0.043 d 0.25 0.40 0.010 0.016 g 0.65 bsc 0.026 bsc h 0.05 0.15 0.002 0.006 j 0.13 0.23 0.005 0.009 k 4.75 5.05 0.187 0.199 l 0.40 0.70 0.016 0.028 notes: 1. dimensioning and tolerancing per ansi y14.5m, 1982. 2. controlling dimension: millimeter. 3. dimension a does not include mold flash, protrusions or gate burrs. mold flash, protrusions or gate burrs shall not exceed 0.15 (0.006) per side. 4. dimension b does not include interlead flash or protrusion. interlead flash or protrusion shall not exceed 0.25 (0.010) per side. b a d k g pin 1 id 8 pl 0.038 (0.0015) t seating plane c h j l on semiconductor and are trademarks of semiconductor components industries, llc (scillc). scillc reserves the right to make changes without further notice to any products herein. scillc makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does scillc assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. atypicalo parameters which may be provided in scill c data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. all operating parameters, including atypicalso must be validated for each customer application by customer's technical experts. scillc does not convey any license under its patent rights nor the rights of others. scillc products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body , or other applications intended to support or sustain life, or for any other application in which the failure of the scillc product could create a sit uation where personal injury or death may occur. should buyer purchase or use scillc products for any such unintended or unauthorized application, buyer shall indemnify and hold scillc and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthori zed use, even if such claim alleges that scillc was negligent regarding the design or manufacture of the part. scillc is an equal opportunity/affirmative action employer. publication ordering information japan : on semiconductor, japan customer focus center 4321 nishigotanda, shinagawaku, tokyo, japan 1410031 phone : 81357402700 email : r14525@onsemi.com on semiconductor website : http://onsemi.com for additional information, please contact your local sales representative. nup6101dmr2/d micro8 is a trademark of international rectifier. literature fulfillment : literature distribution center for on semiconductor p.o. box 5163, denver, colorado 80217 usa phone : 3036752175 or 8003443860 toll free usa/canada fax : 3036752176 or 8003443867 toll free usa/canada email : onlit@hibbertco.com n. american technical support : 8002829855 toll free usa/canada
|
